Last updated November 17, 2026








Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Fence Installation Maintenance Schedule: What to Do and When
Putting sealer on a wood fence in San Francisco in January wastes money. So does waiting until the fog has soaked the boards in February, then painting stain over wood that’s holding moisture. We’ve seen it repeatedly: wood moisture content above 19% during and just after the rainy season, when most sealers and stains need milled wood below 15% to bond and cure. The product sits on the surface and washes off with the next front. This guide covers the maintenance calendar that actually works in San Francisco’s fog belt, with hard dates, pass/fail inspection criteria, product-specific reapplication intervals, and cost figures per linear foot.
Quick Answer
Inspect your fence once a year (April is the ideal month, after the rains and before the dry window), and seal or stain only between May and September when wood moisture is reliably below 15%. Under San Francisco conditions, clear sealers need refreshing every 1 – 2 years, penetrating oils every 3 – 4 years, and film-forming stains every 2 – 3 years on fog-exposed west-side lots. Rot treatment, fastener checks, and hardware torque belong in the same spring inspection every year.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Table of Contents
- The San Francisco Maintenance Calendar: When to Do What
- The Annual Inspection Checklist: Pass/Fail Criteria
- Sealer and Stain Intervals by Product Type in Fog-Belt Conditions
- Application Requirements by Product Type
- What to Do When You Find a Soft Post
- The Probe-and-Decide Protocol
- What Photos to Take and Why the Log Matters
- How San Francisco’s Microclimates Change the Schedule
The San Francisco Maintenance Calendar: When to Do What
San Francisco doesn’t run on a four-season maintenance cycle. It runs on a wet season (roughly November through March), a dry window (May through September), and two shoulder months where the dew point makes a mess of sealers. The calendar below is built around that actual cycle.
- April: Full structural inspection. Rains have stopped, wood has dried enough to read. Rot probing, post plumb check, fastener torque check, end-grain sealant condition, deferred maintenance list. Save all photos with dates in your maintenance log.
- May through mid-June: Primary sealing and staining window. Wood moisture is reliably below 15% and daytime temperatures sit in the 62 – 70°F range – within the application window for nearly every penetrating oil and most film-forming stains we specify.
- Mid-June through September: Secondary window. During dry spells, fog-belt neighborhoods (Sunset, Richmond, Forest Hill) sit in the 55 – 18% moisture band consistently; on west-side lots the second coat often goes down in late August. Peak sun months can push surface temperatures high enough that film-forming products dry too fast on exposed southern-facing panels.
- October: Pre-season touch-up. Seal any end grain that got damaged by summer heat, re-torque any hardware loosened during the dry months. Do not begin a fresh full-boat sealing project in October; the wood will not dry enough before the first rains.
- November through March: Do not seal. Do not stain. Inspect visually after heavy rain fronts: standing water at post bases, pooling along top rails, any softening near the soil line.
For homeowners weighing new build versus maintenance, our guide to Fence Installation in San Francisco covers material and cost from the ground up. Maintenance only saves money if the fence was built to survive the fog in the first place.
The Annual Inspection Checklist: Pass/Fail Criteria
An inspection without pass/fail criteria is just a walk around. Below are the measurements we use on every seasonal check. Handle this with a 4-foot spirit level, a socket set, and a small flathead screwdriver. In San Francisco, where fog drives moisture into end grain from every side, defer to these thresholds rather than to your eye.
- Post plumb: Allow no more than 1/8 inch of lean per foot of post height. A 6-foot post should not lean more than 9/16 inch. Measure on two faces, at least two posts in from a corner.
- Hardware torque: Check the bolt heads on hinges and rail brackets. Most hinges we install carry a manufacturer spec of 15 – 20 ft-lbs; if the bolt spins easily in a finger pull, it’s loose. Tighten it before it ovalled the hinge plate.
- End-grain sealant condition: Every cut end on a top rail, picket, or post cap should have sealant over the raw grain. Any exposed grain with a visible crack deeper than a fingernail means the board is wicking moisture on that end.
- Fastener corrosion rating: Look for brown rust bleed at any fastener head. On fog-belt lots, hot-dip galvanized or stainless steel is the standard; any electro-galvanized or plain steel fastener showing corrosion should be replaced. This is a San Francisco-specific failure – inland fences can use lower-rated fasteners with no trouble.
- Panel-to-rail gap: Measure the gap between the picket/panel and the horizontal rail. More than 1/8 inch of seasonal movement in a rail span indicates the rail’s fasteners have loosened or the wood has dried unevenly; more than 3/16 inch warrants a structural look.
- Post base condition: Clear soil 2 – 3 inches below grade around any post base and probe with the screwdriver. If it pushes more than a quarter inch into the wood, the post is compromised at the rot line.
Run this checklist in April. By the time it’s done, you know how much material to buy before the sealing window opens.
Sealer and Stain Intervals by Product Type in Fog-Belt Conditions
Fog-exposed west-side lots in San Francisco are the toughest maintenance environment in the city. The Sunset and Richmond districts see persistent marine layer that keeps wood damp on a portion of every day; a fence there will go through sealer faster than the same fence in Noe Valley or Bernal Heights, where sun hits the boards for more of the day. The intervals below reflect the fog-belt worst case, not the city average.
- Clear penetrating sealer: Refresh every 1 – 2 years. Products like Thompson’s WaterSeal Advanced Natural and Ready Seal Natural are common here; both need wood below 15% moisture to bond. West-side lots come due every 12 – 14 months. Typical applied cost in San Francisco runs $2.50 – $4.00 per linear foot, both sides.
- Penetrating oil stain (e.g., Penofin Oil-Based, Ready Seal semi-transparent): Refresh every 3 – 4 years. Oil-based penetrating stains link with the wood fiber and hold up to fog better than film-formers. Cost per linear foot: $3.00 – $4.50 both sides.
- Film-forming stain (e.g., Sherwin-Williams SuperDeck solid, Behr Solid Color Waterproofing): Refresh every 2 – 3 years on fog-exposed west-side lots, 3 – 4 years on other lots. Solid film-forming stains are the most weather-resistant product, but they fail by peeling once a seam opens, which makes them higher maintenance in the long run. Cost per linear foot: $4.00 – $6.50 both sides, plus a strip and re-sand every 6 – 8 years.
- Composite fence with UV cap (e.g., Bufftech CertaGrain, ActiveYards Edge with PermaShell): No sealing required, but plan an annual pressure-wash and a UV cap inspection every 5 years. Stain-free doesn’t mean maintenance-free.
If you’re still deciding between wood and composite, the material breakdown in our Driveway & Pavers in San Francisco guide covers the same reasoning used on hardscape: material choice sets lifetime cost before the first maintenance bill arrives.
Application Requirements by Product Type
This is the number most homeowners skip, and it’s the reason a sealer applied in January fails by March. Every sealer and stain has a stated moisture limit and a temperature window. Below are the requirements by product type as printed on the technical data sheet – not as summarized by the paint-department clerk.
- Oil-based penetrating sealer: Wood moisture 12 – 15%. Air temperature 50 – 80°F during application and for 8 hours afterward. No rain within 24 hours. In San Francisco, apply May through September.
- Water-based penetrating sealer: Wood moisture below 15%. Air temperature 50 – 90°F. No rain within 24 hours. Coastal fog doesn’t prevent cure, but dew at night does – check the dew-point forecast the day before.
- Film-forming solid stain: Wood moisture below 12% (tighter than penetrating products). Temperature 50°F and rising at application; no rain within 24 hours. On south-facing panels in June, surface temperature can exceed the manufacturer’s maximum – apply early morning.
- End-grain sealant (e.g., Anchorseal 2): Apply dry, at temperatures above 40°F. Apply immediately after any cut on the fence – no need to wait for a seasonal window.
What to Do When You Find a Soft Post During the Annual Inspection
A soft post is either a $180 – $350 repair or a $500 – $900 full-post replacement, depending on where the rot sits and how far it runs. The decision is mechanical, not aesthetic. Here’s how we make it in the field.
The failure point on a San Francisco wood post is almost always the soil line – the 6 – 8 inches just above and below grade where the fog-moistened wood meets the soil-moistened wood. A post that’s soft at the top cap due to a failed end-grain seal is a different repair than a post soft at the base due to water intrusion under the concrete collar.
Sister-post repair: When the rot runs less than 18 inches above grade and the post is structurally sound below, a sister post is the right repair. A pressure-treated 4×4 is bolted alongside the original post, driven into fresh concrete or a helical anchor, and the panel is reattached. Material cost typically runs $45 – $85 for the sister post, anchor, and hardware; total installed cost $180 – $350. This extends the post’s life another 8 – 12 years in San Francisco conditions.
Full post replacement: When rot runs more than 18 inches above grade, or when the post base has lost more than a third of its cross-section, replace the post. Cost $500 – $900 per post installed, including concrete and hardware, plus the labor to disassemble and rebuild the panels attached to that post. On a fence where three or more posts are compromised, the math usually favors a full rebuild over piecemeal repair.
We’d flag one thing before the repair: check the adjacent posts in the same run. Rot rarely sits on one post alone. If two neighbors are starting to soften, a sister-post repair on the single failed post usually just means a second repair nine months later.
The Probe-and-Decide Protocol
Before a single post gets pulled, we run this protocol on every post in the fence. It takes about 15 minutes for a 150-foot fence.
- Probe at three points: push a flathead screwdriver into the post 1 inch below grade, 4 inches below grade, and at mid-height. Pressure should meet resistance and the tool should not sink more than 1/8 inch.
- Tap and listen: strike the post with the screwdriver handle. A sharp ping means sound wood; a dull thud means rot inside.
- Meter the moisture: a pin-type moisture meter pressed into the base (where it counts) rarely reads below 20% in fog-belt San Francisco even in summer. That reading alone isn’t a fail – post bases in this city are almost always wet. What matters is the probe result and the tap tone.
- Map the posts: on a paper sketch of the fence, note which posts pass, which need sister repairs, and which need full replacement. Note the number of posts in each category.
- Decide: under 10% of posts in the “replace” column → repair individual posts. 10 – 25% → repair and plan a phased post replacement over 12 – 18 months. Over 25% → full rebuild usually beats repair on cost and lifespan.
What Photos to Take and Why the Log Matters
The maintenance log is the cheapest insurance a fence owner can keep, and it’s the first thing we ask for when a homeowner calls about a warranty claim or a contractor quote. Most of the value comes from the photos, and the cost of taking them is essentially zero.
Every April inspection should capture these shots on your phone, filed in a dated folder:
- Post bases, wide shot and close-up: three or four representative posts including any that probed questionable – the photo shows the grade line, the concrete collar, and the wood condition together.
- Hardware close-ups: every hinge, latch, and rail bracket. Corrosion shows up in a photo two months before it’s visible to the eye.
- End-grain condition: top rails and panel ends. This is where a moisture reading starts and where most rot begins.
- Panel-to-rail gap with a tape measure in frame: a photo with a ruler in it is a defensible measurement; a photo without one is a guess.
- The whole fence, one long view: before-and-after each season is the fastest way to spot a slow lean or a sag.
Beyond warranty claims, the log shows a contractor scoping a quote exactly which posts are nearing end of life. On a fence installed with a documented photo record and a signed price upfront – the process we run under our Rowan Construction Group San Francisco home standard – a dated log turns an inspection into a cost estimate.
How San Francisco’s Microclimates Change the Schedule
San Francisco isn’t one climate. A fence in the Sunset lives in a marine layer that keeps wood damp a full month longer in spring than the same fence in Glen Park. That single difference shifts the sealing window and the reapplication interval.
- West side (Sunset, Richmond, Forest Hill): Heaviest fog exposure. Sealing window opens mid-May, closes late September. Clear sealers come due every 12 – 14 months; film-forming stains every 2 – 3 years. Corrosion risk on hardware is highest here.
- Central (Noe Valley, Bernal Heights, Inner Mission, Eureka Valley): More sun hours, lower humidity. Sealing window opens late April. Clear sealer every 18 – 24 months; oil-based stain every 3 – 4 years.
- South and southeast (Excelsior, Visitacion Valley, Portola): Warmer and drier in summer, but wind-exposed. End-grain failure is more common than base rot. Film-forming stains hold 3 – 4 years.
- North (Marina, Pacific Heights, Presidio Heights): Similar to the west side, with slightly more sun. Cedar and redwood fence the most common failure mode; the end-grain sealant step every year is the highest-value maintenance task on the list.
If a fence is being replaced rather than maintained, we recommend composite products like Bufftech or ActiveYards on west-side lots – the sealing savings over 15 years pay a large fraction of the material upgrade. For fences under construction, our Home Additions & ADU in San Francisco guide covers how fence lines are set during site prep, which affects everything that follows.
Common Mistakes to Avoid
- Sealing or staining in the rain season. It’s the mistake we see most. Wood moisture above 15% prevents proper bonding, so the product sits on top and washes off.
- Skipping the end-grain sealant step. On San Francisco’s fog-exposed lots, end grain is where rot starts. A 15-minute pass with a brush and a can of Anchorseal every year is the cheapest rot prevention available.
- Using lower-grade fasteners. Electro-galvanized or plain steel fasteners fail fast on the west side. Specify hot-dip galvanized or stainless steel.
- Pressure-washing at too high a pressure. Above 1,500 PSI on wood fences, you strip the softer grain between the growth rings. Stay at 1,200 PSI or lower, and use a fan tip.
- Ignoring a soft post until it fails. A $180 sister-post repair today is a $500 full-post replacement in two years, plus panel damage from the lean.
- Skipping the maintenance log. Photos with dates are the difference between a warranty claim that’s honored and one that isn’t.
- Applying a solid stain over existing penetrating oil. The film-former will peel within a year because the oil prevents the bond. Strip first, or stay with a penetrating product.
See the difference
Before
After
Before
After
Before
AfterWhen to Call a Professional
Most of the annual checklist is safe homeowner work: probe the posts, torque the hardware, photograph the details. Call a pro when you find a post more than a third compromised at the base, when three or more posts in a single run have gone soft, when a fence panel has moved more than 3/16 inch at the rail, or when repair versus rebuild is a close call. On a San Francisco lot, post replacement on a fog belt fence is not the place to save money. A trained crew will pull, sister, or rebuild a compromised post in a single visit, document what was found with photos, and leave with the fence back to spec. Rowan Construction Group San Francisco offers free estimates in San Francisco – call (844) 797-6388.
Frequently Asked Questions

Clear sealers: every 1 – 2 years on fog-exposed west-side lots, every 18 – 24 months elsewhere. Penetrating oils: every 3 – 4 years. Film-forming solid stains: every 2 – 3 years on the west side, 3 – 4 years inland. Apply only between May and September, when wood moisture reliably drops below 15%.
No. During and just after the rainy season, wood moisture in the fog belt typically stays above 19%, and most sealers require below 15% to bond. The product sits on the surface and washes off with the next rain. April inspection, May-to-September application.
A sister-post repair runs $180 – $350 installed when rot is less than 18 inches above grade. A full post replacement runs $500 – $900 installed, including concrete and hardware and the labor to rebuild the panels. The threshold where replacement wins is rot above 18 inches or more than a third of the cross-section lost.
Push a flathead screwdriver 1 inch below grade and again 4 inches below. If it sinks more than 1/8 inch, the post is compromised. Tap the post with the handle – a dull thud instead of a sharp ping means rot inside. Do both checks in April, before the sealing window opens.
Yes, just a lighter one. Products like Bufftech CertaGrain and ActiveYards Edge with PermaShell don’t need sealing, but they benefit from an annual pressure wash at 1,200 PSI or lower, a hardware check, and a UV cap inspection every 5 years. Stain-free isn’t the same as maintenance-free.
May and June. Wood moisture is reliably below 15%, daytime air temperature sits between 62 – 70°F, and the dew point is high enough that overnight moisture doesn’t interfere with cure. September is the second-best window. Call (844) 797-6388 for a free estimate on a full fence maintenance package – we quote a written price before any work begins.
The Bottom Line
San Francisco fence maintenance is a schedule, not a set of tasks. Inspect in April with pass/fail criteria in hand – 1/8 inch lean per foot of post height, end-grain sealant condition, fastener corrosion. Sealer and stain only in the May to September dry window. Match the reapplication interval to the product type and the microclimate the fence actually sits in. Log every photo. When you find a soft post, probe-and-decide rather than guess. Handle those four steps and a wood fence in the fog belt lasts substantially longer than the same fence on a schedule built for a dry climate.
If you’d rather hand the calendar to someone who’ll show you the photos and the written price before any work starts, Rowan Construction Group San Francisco can do exactly that. Call (844) 797-6388 for a free estimate – we’ll walk the fence line, document every post, and quote the scope in writing.
Written by the team at Rowan Construction Group San Francisco.


